Dr. Clark Whole House Filter, Version 3

Dr. Clark Whole House Water Filter Kit (Version 3)* w/ board

Automatic and Programmable
Part List for Version 3
Hot Backwash Whole House Water Filter
Purity
Backwash
Unique Design with Hot Water Cleaning
Loose Carbon Media
Fully Automatic
Superior Filtration
Large Filter
Economical
Easy Install
Complete Coverage
Does Not Create “Hungry Water”
No Additives”
Plumbers Instructions”
Guarantee
Considerations Before You Purchase
Whole House Water Filter Guarantee:
Why Gas-Powered Water Heater?

FREE REPORT: ABILITY OF ACTIVATED CARBON TO REMOVE VARIOUS SUBSTANCES FROM WATER

Automatic and Programmable

Dr. Clark Whole House Water Filter - Version 3 includes a Computerized Main Control Valve. When you receive it the valve is set to 10 minutes backwash plus 6 minutes rinse cycle. This equals 16 minutes total x 4 gallons per minute (GPM) = 64 gallons.

You can reduce the 64GPM water consumption to 40 GPM on the Version 3 Filters by reducing the backwash time to 6 minutes backwash and rinse time to 4 minutes (10 minutes x 4 GPM = 40 gallons per backwash.

Further on Version 3 Filter you can adjust the backwash to always happen at the same time of the week. You have a choice between every day to every 99 days. Version 1 can backwash every day to every 12 days.

Parts List for Version 3

1. Water Filter Tank (9” by 48”)
2. Control Valve with Micro-Switch
3. Transformer: 24V AC, 1.25A
4. Pre-washed Coconut Carbon in Whole House Filter, 1 cubic foot (inside filter)
5. Two Normally Open Automatic (Solenoid) In-Line Valves
6. Two Normally Closed Automatic (Solenoid) In-Line Valves
7. Two filter housing (10 inches tall) for Backwash and Carbon Debris Filter
8. Tool for removing 10 inch filter housings
9. Coconut carbon and cartridge for Backwash Filter
10. Fiber filter for collecting carbon debris
11. Leads with color coding for easy installation
12. Tube for backwash outlet
13. Teflon tape
14. Thermometer
15. Instructions with Diagram
16. Two page Service Manual Card (inside Main Filter Housing)

Hot Backwash Whole House Water Filter

Designed by Dr. Clark
In 2007, after 2 years of researching many filter combinations and filter media Dr. Clark finally found this filter and filter medium to meet her requirements. We have worked tirelessly on improving the design of this filter keeping in mind Dr. Clark’s strict requirements.

The basic idea that hot carbon is more easily cleaned in hot water than cold is perhaps intuitive for most people that do dishes and laundry. There may also be a more scientific explanation because hot water has been proven to expand the tiny little pores in the activated carbon, hence making it easier for pollutants to be dislodged from the trap.

Purity

Specially processed and pre-hot-washed Activated Carbon from Coconut Shells is used as filter medium.

Backwash

Since the filter does not contain tightly packed filter media, it back-washes effectively, washing out impurities.

Unique Design with Hot Water Cleaning

This is the first filter on the market that takes advantage of the fact that carbon pores expand in hot water allowing for a more effective regeneration.

Loose Carbon Media

Only loose carbon can be effectively regenerated. During backwash the carbon media is lifted up and tumbled around in hot water. This is not possible with tightly packed filters. Loose carbon also prevents the formation of “water ways” in the carbon. Water follows the law of least resistance and with time it carves a water way right through your filter. Those waterways are destroyed during backwash.

Fully Automatic:

The filter is fully automatic and performs a Hot Water Backwash every 1 to 99 days (your choice). Dr. Clark recommends every 5 days.

Superior Filtration:

Activated Carbon is known for being the most effective filter medium for organic solvents, such as oils, benzene, and chlorine. Those are the type of toxins Dr. Clark is most concerned with.

Large Filter

The shear quantity of carbon (1 cu ft) contributes to the filters effectiveness.

Economical:

Water consumption has been reduced to 40 GPBW on the Version 3 Filters by reducing the backwash time to 6 minutes backwash and rinse time to 4 minutes (10 minutes x 4 GPM = 40 gallons per backwash. Main filter medium (1 quibic ft carbon) does not need to be changed more often than once every 3 to 5 years.

Easy Install:

We now have the filter “pre-installed” on a board so that you don’t have to pay your plumber to become confused about how to install it. We have also recently simplified the electronic circuits, making for a “fail-proof” installation.

Complete Coverage:

You get rid of toxic elements before the water enters the house. For a full list of these elements and the filters effectiveness on them visit: http://drclarkstore.com/activatedcarbon.html

Does Not Create “Hungry Water”

The filter does not take out all your minerals from the water and therefore does not attach to your plumbing system as “hungry water does”.

No Additives

The filter does not add any chemicals to your water.

Many prominent researchers agree with Dr. Clark that chlorine is a killer. It is even defined by the US EPA as a pesticide! Dr. Robert Carlson, a highly accomplished researcher from the University of Minnesota who’s work is sponsored by the Federal Environmental Protection Agency, sums it up by claiming, “the chlorine problem is similar to that of air pollution”, and adds that “chlorine is the greatest crippler and killer of modern times!”

Plumbers Instructions:

Quick Reference Guide
When you open the image, please maximize your browser windows to see the instructions clearly.

Front

Back

Before you start installation please measure the water pressure on the house with a pressure tester (available at plumping supply stores). If it’s over 55 then install a pressure regulator to 50 psi, if you choose not to do that the warranty is voided.

Each board is tested for leaks at 55 psi before it is sent out. We guarantee that the assembly board is working properly under 55 psi when it leaves our facility.

Considerations Before You Purchase:

Filter must be installed vertically (does not work in horizontal position) with inflow, outflow and drain in accordance with manufacturer’s recommendations to meet applicable building codes.

Installation typically costs $600. We don’t recommend you install this by yourself.

Additional costs will apply if you want to operate the system outside USA on another voltage because you need special transformers.

NOTE:

Before installing the filter make sure you have a gas-powered water heater installed. Dr. Clark prefers gas-powered water heaters over electric water heaters.

NOTE:

This system works on ¾ inch plumbing system. You may experience lack of pressure if you use 1” plumbing. If you want a 1 inch system you can special order it from us.

NOTE:

Should you want to filter well water you are advised to install an inline UV sterilization system (call Customer Service for purchasing those). Connect it on the Main Water Inn, before Whole House Filter.

Attention: This filter is not designed to work in tandem with any other water purification equipment (except UV system). It’s up to you to decide if you disconnect other purification equipment. Do your research, and please do not ask us, we cannot answer because of possible liability from other manufacturers.

NOTE

This filter is sold as a kit. Once correctly assembled by your plumber the filter can be set to perform an automatic hot-water backwash every 5 days.

We have not gotten any approval for this system from any government agency. This system may not be compliant to building codes. Having the system installed may cause you to not pass building inspection, depending on regulation in your area. Fore example your area regulations may state that you can only solenoids made with copper and they may state that you cannot use any check valves made from PVC. Further some regulations may state that you cannot put hot water into the carbon tank or that you cannot use cPVC plumbing. For this reason, install you may not pass building inspections when you sell the house. We advice you to simply uninstall the system and take it with you.

Whole House Water Filter Guarantee:

We offer a 90 day money back guarantee. Should you not be happy with the system for any reason, please return it for a refund, minus a 15% restocking fee. However, should any part of the system be defective you are entitled to a 100% refund or exchange, after evaluating the part in question. No refund on shipping.

Warranty

You get 1 year manufacturer guarantee on all the valves. We guarantee that the assembly board is working properly under 55 psi when it leaves our facility. Standard house pressure is 50 psi. If your pressure is greater than 50 psi it can destroy your faucets. Should your house have higher psi than 55 then please install a pressure regulator to 50 psi, if you choose not to the warranty is voided. (each board is tested for leaks at 55 psi before it is sent out)

Once you install the filter we cannot take it back because of leakage and we do not pay a plumber to repair it. Please make sure that the board is tested by your plumber before final installation. We do not pay service charges in case the system is not working. We only guarantee the parts themselves. Please ask your plumber for a service guarantee. We are not liable to cover any plumbing bills under any circumstances.

Why Gas-Powered Water Heater?

All traditional water heaters are made in the same way, with glass lining. This is industry standard. However electric heaters have a very hot element in direct contact with the water. This is what Dr. Hulda Clark did not like, according to her theories the hot element leached metals into the water.

Here is a link to a water heater spec sheet:
http://www.hotwater.com/lit/spec/res_gas/ARGSS01406.pdf

They don’t talk much about glass lining but in 6th paragraph they mention GLASS COATING. They are protecting it from rust but at the same time protect the water from any contact with hot metal. Basically they pour hot glass into the tank after its made and code it with glass.

One of the main companies producing hot water heaters of this type are:

A. O. Smith Water Products Company
500 Tennessee Waltz Parkway
Ashland City , Tennessee, USA 37015
1-800-527-1953 dial for service info ext 4 ext 3
FAX: 1-615-792-2163
help@hotwater.com